Como solucionar falhas elétricas no material rodante?

Troubleshooting electrical faults in rolling stock can be complex. 1. Identify the problem: Begin by understanding the specific issue or symptom. 2. Inspect and test connections: Check all electrical connections for loose or corroded contacts. 3. Check fuses and circuit breakers: Verify if any fuses or circuit breakers have tripped or blown. 4. Use a multimeter: A multimeter is a useful tool for troubleshooting electrical issues. 5. Inspect relays and switches: Examine relays and switches for proper operation. 6. Investigate grounding issues: Poor grounding can cause various electrical problems. 7. Consult wiring diagrams/manuals: Refer to wiring diagrams or maintenance manuals provided. 8. Conduct isolation tests: etc

The below sequence is the most standardized approach in fault location- 1. Prompts on Driver Display Unit (DDU): Modern-day Rolling Stock is well equipped with appropriate alarms and warning signals on DDU. Identify the subsystems generating a prompt and note down the alarm/warning code. These codes can be in alphanumeric format. 2. Refer to the Maintenance Manual: For the alarm/warning code observed from DDU, read the code description. Eg. The error can be from the over-temperature observed in the traction motor. 3. Check Status: Check the health status of all the protection circuits and switchgear for the corresponding system. Eg. In the case of Motor over-temperature, what is the status of the thermal relay?

Depending on the nature of the fault, where possible locking out both mechanically and electrically is a good measure. Over and above knowing the basic electrical wiring diagram, it is imperative to know the principle of operation of both operating components on the equipment at large as well as the components that form part of the circuit

Fault Isolation is done by below means: Sensed Reversible Isolation - A relay will sense the signal threshold lanes mits and generate actuation command for breaker or contactor. Eg. Thermal relay will open the main contactors for motor. Sensed Irreversible Isolation - Fuse is classic example of sensing element but the isolation is irreversible unlike circuit breaker. Hence the element has to be replaced in such isolation cases. Intervention based isolation - Such isolation are done when sensing elements are damaged and operator has to intervene and isolate the fault. Amongst all isolation above, it is the intervention based isolation which shall be analysed thoroughly while drafting a troubleshooting procedure. Cheers!

The tools are very important. They must measure clearly. You must do calibration every year. Testing equipments are critical.

Post identifying the faulty part, it is essential to identify the level of the part as per the Bill of Material (BoM). Commonly in Rolling Stock, two levels of BoM used are: - Vehicle Level BoM - Sub System Level BoM. The next step is to identify the level of the component in BoM, the level can be a Line Replaceable Unit (LRU) or Shop Replaceable Unit (SRU). The next step is to be equipped with suitable maintenance tools and diagnostic tools (Portable Test Equipment) As a final step after replacement make sure to check as below: - Continuity Check - Functionality Check - Software/Firmware Version Check - Torque Marking - Event Recorder in order

Diagnosis, identification and repair are the stages of troubleshooting the fault. If you follow the standarts you can fix the problem easily.

The following steps lead to effective troubleshooting: - Keep the maintenance manual handy during the process. - Make sure the faulty device, post repair/replacement is rewired as per the design schematics. - Equipment is loaded with the latest software. - Use portable test equipment to ensure all the protective breakers and switch gears perform as intended. - If batteries are used, ensure the warm-up procedure as performed suitably. - Refer to the checklist and startup procedure before interfacing the device within the sub-system and the entire system. - If the replaced/repaired component is safety critical, make sure it is under observation for some time. - Fill up the troubleshooting checklist and the issue log with the solution.

You should learn all the information you can from experienced technicians. Just learning is not enough. You should record it and then pass it on to those who need it.

For troubleshooting,you must be aware about the train control drawing (emergency, parking brake,door, compressor...), knowing the function of each component in the circuit like relay or bush button you must study relation between pneumatic system and electrical . I agree with you troubleshooting related to experience of technicians but it depends on the study first and know the function of each component and if failed what will happen.

Rolling Stock is a multidisciplinary system including, Electrical, Electronics, Mechanical, Controls, etc. Peer learning plays a vital role in understanding and assessment of faults. 1. Try to gather and understand the impact on electrical systems due to faults in other systems like Train Control (TCMS), Load Distribution Network, LV (110V & 24V) power supply, HVAC, etc. These gathered repositories can be later implemented during the designing of the electrical system such that better reliability in design can be achieved. 2. Volunteer for RCA performance of cross-functional teams like Validation, Change Management, etc. 3. Contribute system-level details with the Reliability & Maintainability team to FMECA, RMAP, RAMS plan.