Como você calibra e mantém seu multímetro para obter resultados precisos?

1) The first thing is to check the calibration label. This is usually at the back and mentions the validity due date, similar to an expiration date in perishable goods. 2) The other good practice is to observe the BAT LOW symbol is not present in the LCD display (for DMM). 3) In addition, when conducting important tests, I would recommend to have a standard measurement reference equipment in the lab (V, I, R, etc) to make sure the reading is accurate. 4) The storage temperature is also important. In some countries where extreme weather is present, it's important to keep the instrument within the manufacturer's storage temperature and humidity range. 5) Be aware of potential EMF interference in the space where you conduct measurements.

Checking the battery of your multimeter is a crucial step in ensuring accurate measurements and reliable performance. Start by locating the battery compartment and visually inspecting the battery for any signs of damage or corrosion. Then, use the multimeter's voltage measurement function to check the battery's voltage, ensuring it matches the rated voltage. If the reading is significantly lower than expected, replace the battery with a new one of the same type and rating. Properly dispose of the old battery according to local regulations. Incorporate regular battery checks into your maintenance routine to prevent unexpected failures and maintain consistent performance from your multimeter.

To calibrate and maintain your multimeter for accurate results: 1. Check Calibration Period: Refer to the manufacturer's recommended calibration interval and send it for professional calibration if needed. 2. Perform Basic Self-Tests: Use the multimeter's built-in tests (if available) to check for basic functionality. 3. Use Reference Voltage/Resistance: Compare readings with a known reference voltage or resistance to verify accuracy. 4. Keep Clean and Dry: Ensure the multimeter and its probes are clean, dry, and free of dust or corrosion. 5. Inspect Probes: Regularly check for wear or damage to the probes, replacing them if needed. These steps will help keep your multimeter accurate and reliable!

Battery operation for low quality vs standard one. Conventional equipment either gives a low battery message or does not power up when the battery energy level may lead to incorrect readings. Low quality equipment operate even when a low battery produces incorrect operation and readings.

Cleaning the metallic surface of the probes can be done with a soft cloth dampened with isopropyl alcohol. Another effective method is using a small pen with a fiberglass brush. This tool removes carbon deposits and oxidation from the metallic surface without damaging any special coatings, such as gold-plated contact points.

Test Leads Quality Have you ever seen anyone use a dirty test lead? Me neither. It is clear that AI has a long way to go. EEVBlog makes emphasis on test leads quality by the continuity speed of response. After a few videos it appears that gold tipped test leads deliver faster continuity response. It is rare to have dirty test leads and even rarer to have them corroded. They are used and stored in clean and dry environments. Not so sure if anyone tests wet or humid electrical equipment. You can try, but results may differ from normal dry operation. Oscilloscopes use probes, DMM use test leads.

Cleaning the probes of your multimeter is essential for ensuring accurate and reliable measurements. Start by disconnecting the probes from the multimeter to avoid accidental damage or electrical shock. Then, use a soft, dry cloth to gently wipe away any dirt, debris, or residue from the probe tips. For stubborn residue, you can moisten the cloth with a mild cleaning solution or isopropyl alcohol. Be sure to dry the probes thoroughly before reconnecting them to the multimeter. Regularly cleaning the probes helps maintain proper electrical contact and prevents interference with measurements, ensuring consistent performance from your multimeter.

Continuity testing with a multimeter verifies if an electrical circuit is complete. Set the multimeter to continuity mode, ensuring the circuit is disconnected. Touch the probes together to establish a baseline reading. Then, place one probe at each end of the circuit. If the circuit is continuous, the multimeter emits a sound or displays continuity. It's vital for troubleshooting and confirming wiring integrity.

Continuity mode is to test open circuits and not accuracy. Test leads can be tested for open with continuity prior test. But it does not add accuracy. The big problem is that accuracy is not properly understood. Some equate accuracy to quality, but it is not. Item 3 mixes continuity test with measurement range null value. Prior measuring voltage, test leads are shorted to ensure reading is zero. If not it can be nulled.

Null Zero Null zero does not mean there is no voltage/current thru the test leads. It means any V/A leakage is nulled for the reading. Resistance measurement can be nulled to zero. However there is current flowing thru the test leads. The DMM sources current and measures the voltage of the DUT. The quotient of the measured voltage and the source current is the estimated DUT resistance.

Accuracy does not mean that Accuracy means that the reading is within x values to that national metrological standard. This in turn adheres to the SI defined reference standard. To verify accuracy, instrument needs to be sent to a calibration lab. Few people have the reference testing references standard. Those may have lower accuracy than an accredited lab. Then, those standards need to be periodically tested for traceability.

Handling There is no need to turn it off, if the battery is to be removed. Most units have auto shut off after x time of inactivity. This may be a nuisance when operating for a long time and no means to disable it. Instead, ensure DMM powers up on intended measurement range if not auto ranging. Test leads must be placed in correct positions too.